• <strike id="1movb"></strike>
    <th id="1movb"><video id="1movb"></video></th>
      <strike id="1movb"><sup id="1movb"></sup></strike>
      <object id="1movb"><sup id="1movb"></sup></object>
      <code id="1movb"></code>

    1. <big id="1movb"><nobr id="1movb"><kbd id="1movb"></kbd></nobr></big><code id="1movb"><nobr id="1movb"><track id="1movb"></track></nobr></code>
    2. <code id="1movb"></code>

      <th id="1movb"><option id="1movb"><acronym id="1movb"></acronym></option></th>
    3. <center id="1movb"></center>

      新聞動態
      新聞動態 當前位置:首頁>新聞動態>新聞動態

      安裝與調試

      網址:www.www.jumptotheweb.com  2021-05-20  作者:admin    閱讀:

      安裝與調試
      Installation and debugging
      1. 安裝前,一定要檢查各零件是否良好,潤滑油是否上足,螺栓有無松動,與其有關技術數據是否相符。
      1. Before installation, check whether the parts are in good condition, whether the lubricating oil is sufficient, whether the bolts are loose, and whether the relevant technical data are consistent.
      2. 安裝時,一定要保持基礎布置平面水平180°;啟閉機底座與基礎布置平面的接觸面積要達到90%以上;螺桿軸線要垂直于閘臺上橫梁的水平面;要與閘板吊耳孔吻合垂直,避免螺桿傾斜,造成局部受力而損壞機件。
      2. During installation, it is necessary to keep the foundation layout horizontal °; The contact area between the hoist base and the foundation layout plane should reach more than 90%; The screw axis should be perpendicular to the horizontaltuijianwww.slms1688.comwww.kaiyejixie.com.cnpaimen.89ix.comjianchajingj.75ix.cnwww.gelidunmoju.com.cn  www.fengguanjiagong.com plane of the cross beam on the abutment; It should be vertical to the ram lug hole to avoid the inclination of the screw, which will cause local stress and damage the parts.
      3. 安裝后,一定要作試運行,一作無載荷試驗,即讓螺桿作兩個行程,聽其有無異常聲響,檢測安裝是否符合技術要求。二作載荷試驗,在額定載荷下,作兩個行程,觀察螺桿與閘門的運行情況,有無異?,F象。確認無誤后,方可正式運行。在載荷運行一段時間后,要進行首次保養,把機內新機件磨擦產生的金屬沫特別是螺桿、螺母、渦輪、渦桿,要輕洗干凈,涂上潤滑油,密封嚴實,繼續使用。
      3. After installation, it is necessary to conduct trial operation. First, it is necessary to conduct no-load test, that is, let the screw make two strokes, listen to whether there is abnormal sound, and check whether the installation meets the technical requirements. The second is the load test. Under the rated load, make two strokes to observe the operation of the screw and the gate and see if there is any abnormal phenomenon. After confirmation, it can be put into operation. After a period of load operation, it is necessary to carry out the first maintenance. The metal foam generated by the friction of new parts in the machine, especially the screw, nut, turbine and vortex bar, should be gently cleaned, coated with lubricating oil, tightly sealed, and continue to use.

      聯系電話
      18703286111

    4. <strike id="1movb"></strike>
      <th id="1movb"><video id="1movb"></video></th>
        <strike id="1movb"><sup id="1movb"></sup></strike>
        <object id="1movb"><sup id="1movb"></sup></object>
        <code id="1movb"></code>

      1. <big id="1movb"><nobr id="1movb"><kbd id="1movb"></kbd></nobr></big><code id="1movb"><nobr id="1movb"><track id="1movb"></track></nobr></code>
      2. <code id="1movb"></code>

        <th id="1movb"><option id="1movb"><acronym id="1movb"></acronym></option></th>
      3. <center id="1movb"></center>

        日本丰满妇人成熟免费中文字幕_天堂AV无码AV一区二区三区_永久天堂网 av手机版_强行扒开双腿疯狂视频